See r25218 See comment 10, output from dmesg on my system.
Sat May 14 2011: DNS lookup of 'XXXXX.dyndns.org' gives IP# '83xx.xx' Sat May 14 2011: Checking for IP# change, connecting to checkip.dyndns.org(2.70) Sat May 14 2011: No IP# change detected, still at 83Some further observations, I had the ip addr stored in cache as 226.63.
I then did the following: Deleted ddns.log, inadyn_ip.cache and inadyn_time.cache, then rebooted the router to pick up a new IP Addr. I then tried deleteing the contents of the two cache files and the log but leaving the files there and rebooted the router.
So I'm sure it depends on timing means it probably only occurs with certain drives or partition setup.
Since nobody reported this before and I have only done a few changes that normally shouldn't cause this (added a few rm's to cleanup the output on webif), I'm going to try if the rm's have any effect.
I'd wager a guess that the tutorial is probably out of date. : P On Mon, Dec 14, 2015, Hernán Beiza [email protected]: Yes, is very old...
I don't knew the inadyn package was older than your recent versions... myalphanumericfromdynamic = is a alphanumeric string generated by afraid. I used this tutorials, check it for you have an idea:
I'll post output from dmesg when I have an opportunity. t=275520&start=15, a user reporting identical problem on R7000. "/dev/sda mounted to swap" is written to /tmp/whenever hotplug triggers a mount process and the webif just displays the contents of the generated file.
Here's the output from dmesg: dmesg | grep sd sd 0:0:0:0: [sda] 3907024896 512-byte logical blocks: (2.00 TB/1.81 Ti B) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 17 00 10 08 sd 0:0:0:0: [sda] No Caching mode page found sd 0:0:0:0: [sda] Assuming drive cache: write through sd 0:0:0:0: [sda] No Caching mode page found sd 0:0:0:0: [sda] Assuming drive cache: write through sd 0:0:0:0: [sda] No Caching mode page found sd 0:0:0:0: [sda] Assuming drive cache: write through sd 0:0:0:0: [sda] Attached SCSI disk EXT3-fs (sda1): warning: maximal mount count reached, running e2fsck is recommended EXT3-fs (sda1): using internal journal EXT3-fs (sda1): mounted filesystem with writeback data mode EXT3-fs (sda3): warning: maximal mount count reached, running e2fsck is recommended EXT3-fs (sda3): using internal journal EXT3-fs (sda3): mounted filesystem with writeback data mode [email protected]:~# I need additional info, as it does not occur on my test installs. Output from top after flashing Build 25203 on AC68U: Mem: 45944K used, 209484K free, 0K shrd, 7256K buff, 15644K cached CPU: 16.2% usr 34.5% sys 0.0% nic 48.9% idle 0.0% io 0.0% irq 0.2% sirq Load average: 1.03 1.08 0.69 3/59 28213 From the "top" output it looks like some problem with the start/stop handling that obviously calls hotplug swap multiple times.
Leave the username and password boxes as they are and select Next, then Select Finish.
the actual DDNS scheme it uses is not supported by us, however we can use it to make plain http(s) requests.
t=1758930 In red appears the alphanumeric string that I mean in the last post Thanks for your time!Tags: Adult Dating, affair dating, sex dating